*ANSWER* Stuck on #4
 

To calculate I generated several data sets each of two points where y=sin(pi*x). For each dataset, I generated a hypothesis (a slope a) that minimized the squared error for each of the two points. I did this by calculating the error as , differentiating with respect to a, setting the result to zero and solving for a. This gave me . If I then average my per-dataset slopes (the a's), I get 1.42.

This seems wrong, not only as it's not an available choice (:)) but also because it does not yield a smaller bias than, for example, .79.

I've seen suggestions to use linear regression to calculate the a's, but I don't think that's where I'm going wrong (not only that, but I'm not sure how to do the linear regression without an intercept term).

Re: *ANSWER* Stuck on #4
 

Your procedure is correct. Just to address the above point without commenting on the correctness of your calculation, there is an available choice for your answer, and there is no requirement that the slope is less than 0.79.

Re: *ANSWER* Stuck on #4
 

For what it's worth, I think you're calculating 4 correctly. After 10^6 runs, my average a was 1.4301. It was unsettling to not see my answer among those listed, especially since the others depend on correctly interpreting this question. It would be nice to get further corroboration, simply because none of the above doesn't mean 1.43 was correct.

However, I believe your bias calculation may be off, as your conclusion is different than what I obtained despite having roughly the same a.

Re: *ANSWER* Stuck on #4
 

I calculated it in two different ways and I get a consistent answer that is higher than answer [d] (0.79x). I am unsure as to how far away the answer must be to consider it answer [e] ("None of the Above")?

The difference between answers [c] and [d] is 0.34x. May I assume that if my answer is 1.13x or above (from 0.79x + 0.34x = 1.13x) then [e] "None of the above" is the correct answer (and viceversa)?

I need guidance as to how to determine, in general, how far is "far away" so that I can decide between answers [d] and [e].

Thank you.

Juan

Re: *ANSWER* Stuck on #4
 

Juan, after the derivative of the mean squarred error have you arrived to ?
If so, answer is IMO (I haven't send my answers) clearly upon 0.79
Good luck!
Isidro

Re: *ANSWER* Stuck on #4
 

I think you have a typo, is'n it? For me :clueless:

Re: *ANSWER* Stuck on #4
 

Yes, that's what I got too. So you're saying that with using this formula, you're getting 0.79, and not 1.42 as mentioned in a couple of other threads?

Re: *ANSWER* Stuck on #4
 

Not at all. Using this a I obtain 1.42...

Re: *ANSWER* Stuck on #4
 

Your answer should agree with the given answer to two-decimal-digit accuracy as stated in the problem, or else be considered "none of the above."

Re: *ANSWER* Stuck on #4
 

I also obtain 1.42 with the formula you mention which is based on deriving WRT "a" and equalling to zero to minimize. I also calculated 1.4 by finding the "a" for each value of x1 and x2 and then selecting the "a" associated with the smaller mean squared error.

The answer (a = 1.4), which is higher than the case discussed in class, makes sense to me because the line is forced to pass through zero. It can only rotate about the origin. It removes the translational degree of freedom that would otherwise be available when the intercept is included (y = ax + b). In that latter case any two points are used to create the line (the case discussed in class), and there is a high probability of obtaining many more cases with slope close to zero so I would expect "a" to be lower when using y=ax + b (after calculating the average of many cases). It also makes sense that b tends to zero.

Supposing 1.42 is the correct value, should it be [d] or [e]?

To "d", or not to "d", that is the question :D